The information shown on the page is related to Centauri Carbon.
¶ Quick Start
¶ Troubleshooting
¶ Error Messages
- Error: Printhead anomaly detected
- ErrorCode: 101 The heated bed didn't heat up as expected
- ErrorCode: 102 Anomaly in reading the heated bed NTC
- ErrorCode: 103 The print head didn't heat up as expected
- ErrorCode: 104 Anomaly in reading the heated bed NTC
- Error 502: Leveling sensor data collection error
- ErrorCode: 701 Abnormal mainboard fan
- ErrorCode: 702 Abnormal heat break cooling fan
- ErrorCode: 703 Abnormal model fan
¶ Hardware-Related Issues
- The Touch Screen Not Work
- The Touch Screen is Unresponsive and Stuck On the Loading Screen
- The Extruder Shaking On the X and Y Axes or the Motors of X and Y Axes Operating Abnormally
- The Photoelectric Limit Switch Keeps Triggered
- The Photoelectric Limit Switch Not Triggering
- Cooling Fan Noise
- Noisy Printing
¶ Other Issues
- Automatic Heating of the Hotend when Powered On
- Extrusion Abnormality
- The Print Freezes and Stops
- Clogged Nozzle
¶ Parts Replacement
¶ Print Head and Extrusion System
- How to Replace the Nozzle (B0C0C1)
- How to Replace the Hotend Kit(B0C121/B0C131/B0C141/B0C151)
- How to Replace the Thermistor and the Ceramic Heating Plate(B0C0H1)
- How to Replace the Gearbox of the Extruder(B0C011)
- How to Replace the Gear of the Extruder(B0C0F1)
- How to Replace the Extruder Motor
- How to Replace the Motor of the Print Head
- How to Replace the Cutter
- How to Replace the Filament Wiping Assembly(B0C0J1)
- How to Replace the PTFE Tube
- How to Replace the Print Head PCB(B0C091/B0C0G1)
¶ Cooling Fans and Air Filtration
- How to Replace the Model Cooling Fan(B1C041)
- How to Replace the Heat Break Cooling Fan(B1C031)
- How to Replace the Auxiliary Cooling Fan(B1C071)
- How to Replace the Filter of the Chamber Cooling Fan(B1C021)
- How to Replace the Chamber Cooling Fan(B1C011)
- How to Replace the Motherboard Cooling Fan(B1C001)
¶ Sensors and Detection
- How to Replace the Filament Runout Detection(B0C021)
- How to Replace the Heated Bed Leveling Sensor(B0C0A1)
- How to Replace the Circuit Board of the Heated Bed Leveling Sensor(B0C031)
- How to Replace the Z-Axis Limit Switch(B0C041)
- How to Replace the Chamber Thermistor(B0C2N1)
- How to Replace the Camera
¶ Motion and Transmission System
- How to Replace the Timing Belt of the Print Head(B0C111)
- How to Replace the Z-Axis Timing Belt(B0C081)
- How to Replace the X-Axis and Y-Axis Linear Bearings
- How to Replace the Z-Axis Motor
- How to Replace the Z-Axis Lead Screw
- How to Replace the Z-Axis Shaft
¶ Heated Bed and Platform Assembly
¶ Main Control, Power Supply and Cables
- How to Replace the Motherboard(B0C001)
- How to Replace the Power Supply(B0C101)
- How to Replace the Connection Cable of the Print Head(B0C0L1)
- How to Replace Connection Cable of the Touchscreen(B0C071)
- How to Replace the Cable Chain
¶ Lighting and Structural Parts
- How to Replace the Strip Light
- How to Replace the Hydraulic Hinge of the Front Glass Door
- How to Replace the Old Type of Top Frame with a New One(B0C0K1)
¶ How-To Guides
- How to Print at the Full Size
- How to Check Firmware Version Information and Export Log Files
- How to Adjust the Belt Tensioner
- How to Adjust the Tilting Heated Bed
- How to Fine Tune After Automatic Re-leveling
- Time-lapse Requirements
¶ Maintenance Tutorials
¶ Help us improve
If you have any ideas about the wiki pages, please let us know via ELEGOO official feedback channel.